The Hobbywing QUICRUN WP 10BL60 G2 is a 60A waterproof brushless ESC designed for suitable 1/10 scale on-road cars, off-road buggies and short course trucks. It supports 2S and 3S LiPo power and includes a built-in cooling fan for more consistent temperature control.
Compared with the previous generation, the G2 version combines intelligent freewheeling technology, a more compact housing, an upgraded heat-dissipation structure and capacitor overheat protection. It is designed to deliver reliable everyday performance without the complexity of a competition-level sensored system.
This is a sensorless brushless ESC. A sensored brushless motor may be connected, but it will operate in sensorless mode because the ESC does not use the motor sensor cable. A battery connector is not pre-installed and must be added separately.
Quick Fit Check
Vehicle: Designed for suitable 1/10 scale on-road cars, off-road buggies and short course trucks.
Battery: Supports 2-3S LiPo. No battery connector is pre-installed, so a compatible plug must be soldered to the 14AWG input wires.
Motor: Use a suitable brushless motor up to 6000KV on 2S or up to 3500KV on 3S. Recommended 3S systems normally use a 3652 or 3660-size motor.
Motor Connection: Three 4.0mm female bullet connectors are pre-installed. Sensored brushless motors operate in sensorless mode only.
BEC: Fixed switch-mode 6V/3A output. There is no selectable 7.4V BEC setting.
Fan and Programming: The cooling fan and compatible program box use the same port. Disconnect the fan before programming.
Product Specifications
| Product Name |
Hobbywing QUICRUN WP 10BL60 G2 |
| Product Number |
30107300 |
| ESC Type |
Waterproof sensorless brushless electronic speed controller |
| Vehicle Scale |
1/10 scale |
| Continuous / Peak Current |
60A / 360A |
| Battery Input |
2-3S LiPo |
| BEC Output |
Switch-mode 6V/3A |
| Supported Motor Type |
Sensorless brushless motors; sensored brushless motors operating in sensorless mode |
| Recommended Motor on 2S |
KV ≤ 6000 |
| Recommended Motor on 3S |
KV ≤ 3500, normally using a suitable 3652 or 3660-size motor |
| Applications |
1/10 on-road cars, off-road buggies and short course trucks |
| Battery Connector |
Not included or pre-installed |
| Motor Connectors |
4.0mm female gold bullet connectors × 3 |
| Input Wires |
14AWG, 150mm, red × 1 and black × 1 |
| Motor Wires |
14AWG, 60mm, black × 3 |
| Cooling Fan |
30 × 30 × 10mm framed fan, 6V, powered by the built-in BEC |
| Programming Methods |
ESC SET button, LED Program Box and LCD Program Box Pro |
| Programming Port |
Shared with the cooling fan port |
| OTA / WiFi Programming |
Not supported |
| Data Logging |
Not supported |
| Online Firmware Update |
Not supported |
| Dimensions |
46 × 36.5 × 34.3mm (L × W × H) |
| Weight |
82.6g including wires |
Why Choose the QUICRUN WP 10BL60 G2?
60A Brushless Power
Provides 60A continuous and 360A peak current for suitable 1/10 brushless RC platforms.
Intelligent Freewheeling
Improves electrical efficiency and helps reduce operating temperature during partial-throttle driving.
Active Fan Cooling
A mesh-style heat sink, copper thermal paths and built-in fan help move heat away from the power system.
Capacitor Protection
Capacitor overheat protection provides an additional safeguard during excessive thermal load.
IP67-Rated Protection
Designed for normal RC use around rain, splashes, dust, sand and muddy surfaces.
More Compact G2 Housing
The shorter and narrower design makes chassis layout and wire routing easier.
Intelligent Freewheeling for Lower Heat
The QUICRUN WP 10BL60 G2 uses intelligent freewheeling technology to improve drive efficiency during partial-throttle operation. By reducing unnecessary electrical loss, the ESC can operate at a lower temperature and maintain more consistent performance during longer driving sessions.
Intelligent freewheeling cannot compensate for an overloaded setup. Motor KV, gearing, tire diameter, vehicle weight, drivetrain resistance, ambient temperature and driving style must still be considered.
Smaller and Easier to Install
The G2 housing is 2.5mm shorter and 1.5mm narrower than the previous QUICRUN WP 10BL60. The reduced footprint leaves more room for receiver placement, battery wiring and cleaner chassis organization.
The current ESC measures 46 × 36.5 × 34.3mm. Measure the available electronics tray and check body clearance before ordering, especially when the cooling fan is installed directly above the ESC.
Efficient Heat Sink and Fan Cooling
The ESC combines a mesh-pattern heat-sink cover, copper thermal paths on each motor phase and a 30 × 30 × 10mm cooling fan. These components work together to conduct heat away from the power board and maintain airflow over the heat sink.
The fan runs from the built-in 6V BEC. Keep the fan blades clear of wires and debris, and inspect the fan after use in dusty, sandy or muddy environments.
A cooling fan improves heat management, but it does not make an overloaded motor and gearing combination safe. If the ESC repeatedly enters thermal protection, reduce the gearing or vehicle load and inspect the drivetrain.
Capacitor Overheat Protection
The QUICRUN WP 10BL60 G2 includes capacitor overheat protection in addition to its standard low-voltage, ESC overheat and overcurrent protection functions.
If excessive capacitor temperature is detected, the ESC enters protection and reports the condition through a repeating five-flash green LED pattern. Stop the vehicle and allow the system to cool before checking gearing, motor load, wiring and battery condition.
This protection is an emergency safeguard rather than a substitute for correct system setup. Repeated activation indicates that the electrical or thermal load should be reduced.
Choosing a 2S or 3S Motor Setup
| Battery |
Recommended Motor Limit |
Typical Direction |
Important Check |
| 2S LiPo |
KV ≤ 6000 |
Responsive general-purpose 1/10 setup |
Monitor gearing, motor temperature, tire size and vehicle weight. |
| 3S LiPo |
KV ≤ 3500, normally 3652 or 3660 size |
Higher-voltage setup using a motor specifically rated for 3S |
Do not move a high-KV 2S motor directly into a 3S system. |
Suitable 1/10 RC Applications
The Hobbywing QUICRUN WP 10BL60 G2 is intended for suitable recreational 1/10 scale platforms, including:
- 1/10 on-road RC cars
- 1/10 off-road buggies
- 1/10 short course trucks
- Suitable brushed-to-brushless conversion projects
Scale alone does not guarantee compatibility. Heavy vehicles, oversized tires, tall gearing and high-grip surfaces can place substantially more load on the ESC than a lightweight 1/10 buggy or on-road platform.
IP67-Rated Protection for Outdoor Driving
The sealed ESC carries an IP67 protection rating under normal operating conditions. It is designed to resist common outdoor exposure involving rain, splashes, dust and sand.
IP67 does not mean the ESC should remain underwater. Do not intentionally submerge it for extended periods. After wet or dirty use, disconnect the battery, remove debris and allow the electronics to dry fully before storage.
Water and dust resistance are not permanent. Impact damage, worn seals, damaged wires and normal aging can reduce protection over time. The cooling fan should also be checked and cleaned after use in dirty environments.
Three Programming Methods
The ESC supports three current programming methods:
ESC SET Button
Complete throttle calibration, factory reset and parameter adjustment without a separate program box.
LED Program Box
Provides a quick way to view and change common ESC parameters.
LCD Program Box Pro
Uses a larger display for reviewing and changing compatible settings.
Shared Fan and Programming Port
The cooling fan and compatible program box use the same physical port. To program the ESC with an LED Program Box or LCD Program Box Pro, switch off the ESC, disconnect the cooling fan and connect the program box to the fan port using the correct polarity.
Important: connecting the program box to the receiver throttle cable will not work. Reconnect the cooling fan after programming is complete.
Adjustable ESC Parameters
Available settings include:
- Running mode
- Low-voltage cutoff
- Punch level
- Drag brake force
- Maximum brake force
- Maximum reverse force
- Neutral range
- Motor timing
- LiPo cell count
The BEC voltage is fixed at 6V and is not a programmable item on the WP 10BL60 G2.
Available Running Modes
| Mode |
Operation |
Typical Use |
| Forward with Brake |
Forward and proportional braking only |
Racing or applications where reverse is not required |
| Forward/Reverse with Brake |
Brake is applied before reverse engages |
General bashing and everyday RC driving |
| Forward with Reverse |
Reverse responds directly when commanded |
Special vehicle setups requiring direct reverse response |
Throttle Calibration and Protection Status
Throttle range calibration should be completed when the ESC is first installed, when the transmitter is replaced or when the throttle trim or travel settings are changed.
The ESC LEDs indicate operating and protection conditions:
- A repeating red flash indicates low-voltage protection.
- A repeating single green flash indicates ESC overheat protection.
- Three repeating green flashes indicate overcurrent protection.
- Five repeating green flashes indicate capacitor overheat protection.
If protection is triggered, stop the vehicle and inspect the battery voltage, motor load, gearing, drivetrain resistance, fan operation and system temperature before continuing.
Download the Hobbywing QUICRUN WP 10BL60 G2 manual
Frequently Asked Questions
Can the QUICRUN WP 10BL60 G2 run on 3S LiPo?
Yes. For 3S operation, use a suitable brushless motor no higher than 3500KV, normally in the 3652 or 3660 size range, and confirm that the motor is rated for 3S.
Can I use a 6000KV motor on 3S?
No. The 6000KV recommendation applies to 2S operation. The recommended maximum on 3S is 3500KV.
Does the ESC include a battery connector?
No. The battery input wires are supplied without a connector. A compatible plug must be soldered to the red and black 14AWG wires.
Can the ESC run a sensored brushless motor?
A sensored brushless motor may be connected, but it will operate in sensorless mode because the ESC does not use the motor sensor cable.
Is the cooling fan included?
The WP 10BL60 G2 uses a 30 × 30 × 10mm 6V cooling fan powered by the built-in BEC. Check the product package and listing images before installation.
Where should the program box be connected?
Connect the compatible LED or LCD program box to the fan port. Disconnect the fan first. The receiver throttle cable is not the programming connection for this ESC.
Can the fan and program box stay connected at the same time?
No. They share the same physical port. Disconnect the fan before programming and reconnect it afterward.
Can the BEC output be changed to 7.4V?
No. The WP 10BL60 G2 uses a fixed 6V/3A switch-mode BEC and does not include a programmable 7.4V setting.
Does IP67 mean the ESC can remain underwater?
No. IP67 provides protection under normal operating conditions, but prolonged submersion should be avoided. Water and dust resistance may decrease through wear, damage and aging.
Important Installation Notes
- Confirm battery polarity before powering the ESC. Reverse polarity can permanently damage it.
- Disconnect the battery after use to prevent gradual over-discharge.
- Keep the cooling fan clear of wires, body panels and debris.
- Secure all solder joints and insulate the battery connector correctly.
- Calibrate the throttle range before the first run.
- Reduce gearing or load if thermal protection repeatedly activates.
Explore More Hobbywing QUICRUN ESCs
Compare this 1/10 brushless speed controller with other brushed, brushless and crawler models in the Hobbywing QUICRUN ESC collection.
Negara atau wilayah Anda harus sesuai dengan gudang pengiriman
Gudang US
Untuk Gudang US, pesanan biasanya dikirim dalam 1 hingga 2 hari kerja. Pesanan hanya dikirim ke United Status melalui layanan USPS (Pengiriman Gratis untuk pesanan di atas $69), waktu pengiriman memerlukan 3-7 hari kerja.
Gudang EU
Untuk Gudang EU, pesanan biasanya dikirim dalam 1 hingga 2 hari kerja, waktu pengiriman memerlukan 5-10 hari kerja.
Gudang UK
Untuk Gudang UK, pesanan biasanya dikirim dalam 1 hingga 2 hari kerja. Pesanan hanya dikirim ke United Kingdom melalui layanan Yodel/Hermes/DPD (Pengiriman Gratis untuk pesanan di atas $69), waktu pengiriman memerlukan 3-7 hari kerja.
Biaya pengiriman tambahan mungkin berlaku untuk area tertentu, termasuk Highlands & Islands, Channel Islands, Northern Ireland, Isle of Man, dan Isle of Wight.
Gudang AU
Untuk Gudang AU, pesanan biasanya dikirim dalam 1 hingga 2 hari kerja. Pesanan hanya dikirim ke Australia melalui layanan AU Post (Pengiriman Gratis untuk pesanan di atas $79). Waktu pengiriman memerlukan 3-7 hari kerja.
Gudang CA
Untuk Gudang CA, pesanan biasanya dikirim dalam 1 hingga 2 hari kerja. Pesanan hanya dikirim ke Kanada melalui layanan Amazon UPS/FedEx/CA Post (Pengiriman Gratis untuk pesanan di atas $99). Waktu pengiriman memerlukan 3-7 hari kerja.
Gudang Global
Untuk Gudang Global, pesanan biasanya dikirim melalui pengiriman standar dalam 4 hingga 5 hari kerja, dan waktu pengiriman memakan waktu 15-25 hari.
