Quick Fit Check
The CNHL Racing Series LiHV 6400mAh 7.6V 2S 130C Shorty Hardcase Battery combines high capacity with a compact 96mm shorty format for compatible RC racing cars, drift chassis, on-road pan cars and other 2S performance vehicles.
Each battery measures 96 × 46 × 24mm (L × W × H) and weighs approximately 218g. Its hardcase features 5mm bullet terminals with a 5mm bullet-to-XT60 output lead, allowing installation in compatible vehicles with suitable battery retention and electrical connections.
Before ordering: Confirm 2S compatibility, battery-tray dimensions, case height, terminal clearance and vehicle connector type. This is a 7.6V 2S LiHV battery capable of reaching 8.70V when fully charged. Use the higher LiHV voltage only when the complete power system supports it.
Product Specifications
| Brand / Series |
CNHL Racing Series |
| Stock Number / SKU |
HC6401302HV |
| Capacity |
6400mAh |
| Nominal Voltage |
7.6V |
| Battery Chemistry |
High Voltage Lithium Polymer (LiHV) |
| Cell Configuration |
2S |
| Nominal Energy |
48.64Wh |
| Maximum LiHV Charge Voltage |
8.70V / 4.35V per Cell |
| Standard LiPo Charge Limit |
8.40V / 4.20V per Cell |
| Discharge Rate |
130C Continuous / 260C Burst |
| Maximum Charge Rate |
5C Max |
| Battery Interface |
5mm Bullet Terminals |
| Output Connection |
5mm Bullet-to-XT60 Lead |
| Balance Connector |
JST-XH |
| Dimensions (L × W × H) |
96 × 46 × 24mm |
| Approx. Weight |
218g |
| Power Wire Gauge |
12AWG |
| Battery Case |
Shorty Hardcase |
Dimensions may vary by approximately 1–5mm and weight by ±5g. Confirm additional clearance for the 5mm bullet terminals and output lead.
6400mAh 2S LiHV Power in a Compact Shorty Hardcase
The CNHL Racing Series 6400mAh 2S LiHV offers approximately 48.64Wh of nominal energy in a 96mm shorty hardcase. Its compact length makes it suitable for compatible racing chassis that use shorter battery compartments rather than full-length hardcase packs.
With a manufacturer-stated 130C continuous and 260C burst rating, the battery targets demanding brushless systems. Actual current delivery and vehicle performance depend on the ESC, motor, gearing, connectors, temperature and track conditions.
Why Choose This 6400mAh Shorty Battery?
-
6400mAh capacity: High energy reserve for compatible racing, drifting and trail applications.
-
96mm shorty format: Compact battery length for modern RC racing battery layouts.
-
24mm hardcase height: Low-profile installation for suitable battery mounts.
-
130C continuous / 260C burst rating: High stated discharge capability for matched brushless systems.
-
5mm bullet terminals: Modular hardcase power connection for racing applications.
-
XT60 output lead: Connection option for corresponding XT60-equipped vehicles.
-
LiHV chemistry: Supports full charging up to 8.70V when the electronics and applicable race rules permit it.
2S Shorty LiHV Battery for Team Associated RC10L 2026 Re-Release
The 2026 Team Associated RC10L Kit features a redesigned center-mounted shorty LiPo battery system and supports appropriately configured 1S or 2S electronics. This CNHL 6400mAh 2S LiHV offers a high-capacity battery option in a 96 × 46 × 24mm hardcase, with 5mm bullet terminals and an XT60 output lead. Confirm battery retention, ESC voltage support and connector routing before installation. Explore the Team Associated RC10L Battery Collection.
6400mAh Shorty Battery for HPI Stage D10 Drift Car
The HPI Stage D10 uses a 2S power system with XT60 connectivity and adjustable shorty battery mounting positions. This 6400mAh LiHV pack provides additional capacity for longer drift sessions while keeping the 96mm shorty format. At approximately 218g, battery mass can also influence drift transitions and chassis balance. Confirm the mounting arrangement and charge-voltage compatibility. Compare choices in the HPI Stage D10 Battery Collection.
2S Shorty Battery for Team Associated RC10B7.1 and RC10B7.1D
The Team Associated RC10B7.1 and RC10B7.1D use 2S racing power systems with shorty battery configurations. This 6400mAh pack provides a high-capacity 96mm hardcase option for compatible builds, with a 218g battery weight that can be considered during chassis setup. Verify battery stops, connector routing and the permitted charging voltage for your racing class. Browse the RC10B7.1 and RC10B7.1D Battery Collection.
2S Shorty Battery for TLR 22X-4 2.0 AC and DC
The TLR 22X-4 2.0 AC and DC racing buggies can use compatible 2S shorty battery configurations. This 6400mAh LiHV pack offers a compact 96mm length and substantial energy reserve for practice and longer runs. Check the 24mm case height, 218g weight, battery retaining system and applicable race rules. Compare options in the TLR 22X-4 2.0 Battery Collection.
6400mAh 2S Battery for FMS FCX10 Crawlers
For compatible FMS FCX10 trail and crawler builds using 2S power, the CNHL 6400mAh shorty provides additional energy reserve for extended driving sessions. Its 218g weight may affect climbing balance and side-hill stability, so battery placement matters. Confirm tray dimensions, suitable XT60 wiring and voltage compatibility before use. Explore the FMS FCX10 Battery Collection.
Other 2S Shorty RC Racing and Touring Car Applications
This battery can also suit compatible 2S touring cars, drift chassis and custom racing builds designed around a 96mm shorty hardcase. Confirm battery-retainer dimensions, terminal clearance, chassis weight distribution and competition rules. Explore more RC Touring Car Batteries.
6400mAh Shorty vs. 4600mAh Ultra-Thin Shorty
The 6400mAh pack offers approximately 39% more rated capacity than a 4600mAh shorty battery, but is approximately 50.5g heavier and 6mm thicker. The best choice depends on whether the chassis setup prioritizes additional energy reserve or minimum battery mass.
| Specification |
6400mAh Shorty |
4600mAh Ultra-Thin |
| Capacity |
6400mAh |
4600mAh |
| Nominal Voltage |
7.6V LiHV |
7.6V LiHV |
| Dimensions (L × W × H) |
96 × 46 × 24mm |
96 × 46 × 18mm |
| Approx. Weight |
218g |
167.5g |
| Capacity Difference |
Approx. 39% more |
Lower rated capacity |
| Battery Format |
High-capacity shorty |
Ultra-thin shorty |
Choose the 6400mAh pack when the model supports the additional weight and battery height. Consider the thinner 4600mAh battery for chassis setups where low mass, lower battery placement and faster weight transfer are priorities.
5mm Bullet Hardcase Interface and XT60 Output Lead
This battery uses 5mm bullet terminals built into the hardcase. A 5mm bullet-to-XT60 output lead provides the vehicle-side connection. Unlike softcase batteries with permanently attached power wires, the hardcase format allows connection leads to be positioned according to the chassis layout.
Confirm terminal diameter, polarity, insertion depth, lead length and available clearance before installation. XT60 is not directly interchangeable with EC3, IC3, EC5, IC5, TRX or other connector formats.
Use properly insulated and appropriately rated connectors for the actual vehicle load. Never allow the battery's positive and negative bullet contacts to short together.
2S LiHV Charging: 8.70V vs. 8.40V
This is a 7.6V nominal 2S LiHV battery. With a compatible balance charger, it supports charging to 8.70V total (4.35V per cell). Use full LiHV voltage only when the vehicle electronics and any applicable racing regulations permit it.
The battery can also be balance-charged to the standard 2S LiPo limit of 8.40V total (4.20V per cell). This is the more conservative option when full 8.70V compatibility has not been established.
For routine charging, a balanced 1C rate of 6.4A is preferred. The stated maximum is 5C, equivalent to 32A, but this is not the everyday target. Charger output, power-lead ratings, battery condition and event rules may impose lower limits.
Use an appropriate 2S LiHV-capable charger and suitable hardcase charging leads. Always confirm connector polarity and follow the charging equipment's instructions.
Related 2S Shorty Battery Collections
Explore model-specific options for the Team Associated RC10L, HPI Stage D10, Team Associated RC10B7.1 and TLR 22X-4 2.0.
For touring and trail applications, browse RC Touring Car Batteries and the FMS FCX10 Battery Collection.
FAQ
Is this battery compatible with the 2026 Team Associated RC10L?
It is a suitable shorty-format option for the 2026 RC10L kit when configured with 2S-compatible electronics. Confirm the central shorty battery mount, 96 × 46 × 24mm dimensions, 5mm bullet wiring and selected charge voltage before use.
Can I use this battery in the HPI Stage D10?
Yes, for compatible 2S Stage D10 configurations with suitable shorty battery mounting and XT60 connections. Check battery retention, 218g weight and ESC charge-voltage limits before driving.
Is this suitable for Team Associated RC10B7.1 and RC10B7.1D?
It is a high-capacity 2S shorty option for compatible RC10B7.1 and RC10B7.1D builds. Verify the battery mount, terminal clearance and applicable racing rules.
Is this a full-length or shorty LiPo battery?
It is a 96mm shorty hardcase battery, not a conventional approximately 139mm full-length hardcase pack.
Does this battery have an XT60 cable permanently attached?
No. The battery uses a 5mm bullet hardcase interface and a 5mm bullet-to-XT60 output lead rather than a permanently attached XT60 cable.
How does 6400mAh compare with 4600mAh?
The 6400mAh battery provides approximately 39% more rated capacity but weighs about 50.5g more and is 6mm thicker than the referenced 4600mAh ultra-thin pack. Actual runtime differences depend on the vehicle and driving conditions.
Can I charge this 2S LiHV battery to 8.40V?
Yes. It can be balance-charged to the standard LiPo limit of 8.40V. Full LiHV charging reaches 8.70V and requires suitable charging equipment and a compatible vehicle power system.
What charging current is recommended?
For routine charging, a balanced 1C rate of 6.4A is preferred. The stated maximum is 5C, equivalent to 32A, provided the charger and connection hardware support that current.
Can this battery be used for RC racing?
It can be used in racing classes that permit the battery's chemistry, dimensions and specification. Check current race rules, maximum charge voltage and any approved-battery requirements before entering an organized event.
Does the 130C rating guarantee higher acceleration?
No. The 130C specification is a manufacturer-stated continuous discharge rating. Actual acceleration depends on the motor, ESC, gearing, grip, connector, battery condition and chassis setup.
Battery Care Notice
- This is a 2S LiHV battery with a maximum full-charge voltage of 8.70V (4.35V per cell).
- Use full LiHV voltage only when the vehicle electronics and applicable race rules permit it.
- Charging to the standard 8.40V (4.20V per cell) LiPo limit is possible with suitable equipment.
- Do not use 4.38V per cell as the charging target.
- For routine charging, 1C equals 6.4A. Do not exceed the specified 5C maximum or any lower equipment limit.
- Confirm the 96 × 46 × 24mm dimensions, approximately 218g weight and shorty battery mount before ordering.
- Verify the 5mm bullet terminal interface, XT60 output lead and correct connector polarity.
- Do not allow positive and negative bullet terminals to contact each other.
- Secure the hardcase battery and keep leads clear of gears, driveshafts, suspension components and sharp edges.
- For organized racing, confirm charging voltage limits and any battery approval requirements.
- Never charge unattended. Inspect the battery, connectors and cell voltages before use.
- Do not charge or operate swollen, punctured, damaged, overheated or otherwise abnormal batteries.
- Allow the battery to cool before recharging and use a suitable storage program during extended periods of non-use.
- Inspect the battery after crashes, hard impacts or chassis damage.